Pro Series F1 V3.2 2 Pedal Set

Fully Adjustable to your style:

The unique brake pedal geometry allows the brake pedal assembly to be adjustable in six ways, In-Out-Up-Down-Left-Right. The brake preload and stroke are also adjustable. The Brake Module assembly can be moved Left and Right relative to the clutch and throttle pedals on the billet alloy base.

The clutch pedal is adjustable up and down and has a realistic over centre clutch pressure plate release feel. The pressure is also adjustable. The accelerator pedal travel is also adjustable for stroke length and push strength. All these adjustments are supported by a heel riser that has an adjustable heel rest for precise foot control when under extreme racing pressure.

Supporting Firmware:.

The V3.2 Simulator Pedals comes with a dedicated configuration tool – V3.2 SimControl, built in to our electronic firmware, allowing you to set up your pedals intuitively. A key feature of is the ability to set custom signal output maps per pedal. Working together with our all-new Simworx electronic interface, V3.2 SimControl allows for mapping of non-linear pedal output curves, pedal deadzones and brake pedal force. There is the ability to save an unlimited amount of profiles.

With the V3.2 Simulator Pedals being able to cope with very high brake loads, a sturdy mount to your simulator rig is an absolute must. For that reason we supply a billet CNC Machined Base Plate to mount the pedal modules on to.
The V3.2 Baseplate allows flexible and rock solid positioning of the individual pedals.

Minimising Operating Noise.

All the V3.2  Pedals have noise dampening built in to their front and rear stops to reduce user noise. This is especially designed to minimise any noise in domestic situations. The front stops on all pedals have dampening as long as there is load on them. If the stop is wound in too far, i.e not in contact with the base, the dampening effect will not work.

If the pedal angle is not to your liking, there are adjustable mounting brackets to angle it to your desired foot placement. The adjustable pedal stops can then fine tune the pedal to your final optimum position.

Billet CNC BASEPLATE

This baseplate helps to create a solid platform to mount the V3.2 Pedals to on your simulator platform. The brake of the V3.2 Pedals is able to cope with up to 140kg of force, the standard mounting plates of non Simworx rigs may show excessive flex under these loads.

You also receive mounting hardware for the pedals. The pedal plate mounting points for the pedals are slots, these slots allowing lateral adjustment of individual pedals. The slots are recessed underneath the base to house the mounting nuts which fit flush to the underside of the base. They can slide easily, allowing easy adjustment even when the base is hard mounted to a flat surface.

The dimensions of these lateral slots are 110mm for the brake and 80mm for the throttle and clutch. The Mounting Slots on each side of the pedal base allows for easy fitment to any rig including alloy extrusion rigs and allows adjustability forward or back so you can attain perfect pedal positioning.
The Simworx V3.2 Pedals Baseplate fits directly on to earlier SIMWORX SX02Msport Chassis systems.

Features:

• Independent Pedal Carrier Modules in 6061 Aluminium and Carbon Fibre
• Billet CNC Machined Alloy Base
• Hydraulically Loaded Brake
• Load Cell Brake
• Sealed Ball Bearings throughout on all pivots
• Adjustable Brake Preload
• Over Centre Loaded Clutch
• Adjustable Clutch Pressure
• Adjustable Accelerator Pedal Stroke
• Adjustable Accelerator Pedal Push Pressure 
• Billet CNC Anodised Pedal Pads with Carbon Fibre Inserts
• Adjustable Pedal Pads
• Fully adjustable Brake Pedal Pad
• 140kg maximum Brake pressure
• Dampening on Pedal Stops
• Adjustable Heel Rest with Heel Stop
• Dedicated Bespoke Simworx Electronics Interface
• Dedicated V3.2 SimControl Configuration Software
• All CNC Components finished in brilliant Anodise Finish
• USB Plug & Play